Bromsrör på ENV-bakaxel
Bromsrör på ENV-bakaxel
Jag har letat förgäves efter en officiell bild som visar hur bromsrören ska vara dragna och fästade på en ENV-bakaxel. Är det någon som känner till en sån bild? Nyare bilder på ENV-bakaxlar där bromsrören är orörda skulle också vara intressanta.
Re: Bromsrör på ENV-bakaxel
Kollat i länken nedan?
Klicka! Forumsregler
Klicka! Länksamlingen som har "allt"
Klicka! Verkstadshandböcker, typbeteckningar, bilder mm till Amazon
__/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/
Klicka! Länksamlingen som har "allt"
Klicka! Verkstadshandböcker, typbeteckningar, bilder mm till Amazon
__/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/ __/
Re: Bromsrör på ENV-bakaxel
Jag har tittat i verkstadshandböckerna för bromsar och ENV-bakaxel, men hittar inga bilder som visar rördragningen. Jag har även tittat i en del försäljningsbroschyrer samt sökt efter bilder här i forumet, men tyvärr utan resutat.
Re: Bromsrör på ENV-bakaxel
Hello, here are a few pictures of my own work. The lines were hard to bend, but the brakes work.
1959 P12104 UVB #17048
https://plus.google.com/photos/10959092 ... sYGmncrkaQ
https://plus.google.com/photos/10959092 ... sYGmncrkaQ
Re: Bromsrör på ENV-bakaxel
Thank you Luke. I'm looking for pictures that show how the factory fitted the brake pipes on the rear axle. Do you have pictures of your ENV rear axle with the old brake pipes?
Re: Bromsrör på ENV-bakaxel
Sorry, but I do not have any other pictures. Actually installing the brake lines was the hardest part. I think that you can still buy them pre-bent, but I custom made all my own lines. By "fitted to the rear axle:" in the first picture you can see a distribution block (brass T) that gets mounted directly to the axle via a bolt. On the other side, a metal hose clamp is wrapped around the axle and the brake pipe, in order to hold it in place. Other than that, the brake line just sits on the rear axle.
The hardest part is making the proper bends that go to the wheel cylinders (they are a very tight radius). I recommend buying a brake line bender. Also, I did this install with the axle on the car and it was quite difficult. It may be easier to remove the axle. While you are at it, possibly replace the rear differential oil seal. On a side note, the replacement seals are too thick and they need to be milled down about 4 mm in order to get a good seal.
I am glad to see that someone else owns a ENV rear axle. I have had trouble finding information on them as well.
The hardest part is making the proper bends that go to the wheel cylinders (they are a very tight radius). I recommend buying a brake line bender. Also, I did this install with the axle on the car and it was quite difficult. It may be easier to remove the axle. While you are at it, possibly replace the rear differential oil seal. On a side note, the replacement seals are too thick and they need to be milled down about 4 mm in order to get a good seal.
I am glad to see that someone else owns a ENV rear axle. I have had trouble finding information on them as well.
1959 P12104 UVB #17048
https://plus.google.com/photos/10959092 ... sYGmncrkaQ
https://plus.google.com/photos/10959092 ... sYGmncrkaQ
-
- Posts: 70
- Joined: Sat Dec 03, 2011 7:50 pm
- Location: Räfvåla
Re: Bromsrör på ENV-bakaxel
My ENV rear axle is removed from the car. I have sandblasted it, painted it and replaced the seals and bearings. Now I will change most of the brake components. It is common to replace the ENV with Dana 27, but since my car was built with this ENV rear axle I will try to keep it.lukeball wrote:It may be easier to remove the axle. While you are at it, possibly replace the rear differential oil seal. On a side note, the replacement seals are too thick and they need to be milled down about 4 mm in order to get a good seal.
I am glad to see that someone else owns a ENV rear axle. I have had trouble finding information on them as well.
Re: Bromsrör på ENV-bakaxel
Jättestort tack för de där bilderna, Skrotnisse! De är till mycket stor hjälp för mig nu när jag ska bocka till nya bromsrör och har glömt hur de gamla satt.skrotnisse wrote:skickar några bilder hur dom går på min amazon,,är troligen orginal dragning då den vart avställd sen 78 men inget jag kan garantera
-
- Posts: 70
- Joined: Sat Dec 03, 2011 7:50 pm
- Location: Räfvåla
Re: Bromsrör på ENV-bakaxel
roligt och kanse kunna hjälpa till,, är väl det vänstra som eventuellt kan ha nån annan bokning,
dom ser då ut att suttit på samma plats länge
dom ser då ut att suttit på samma plats länge